FEATURES
- Designed to Meet Class 2
Division 1 Protection
- NEMA 4X (IP66) sealed enclosure
- Purge System
- Water proof and dust proof
- Stainless steel construction
- Mid-size footprint
- Flexible mounting options
- Direct or KVM cabling to
host
- LCD screen shielded by a
Tempered Glass Protective
Overlay

CONTACT

HEADQUARTERS
11529 Sun Belt Ct.
Baton Rouge, Louisiana  70809

Phone
800.223.8050
International 001.225.298.0300
Fax
225.297.2440

E-mail
sales@vartechsystems.com

Website
www.vartechsystems.com

 

 

_____________________

Material Specifications

Regulator Body
Zinc w/ Enamel Finish

Regulator Handle & Bowl
Polycarbonate

Rapid Exchange Gauge
Aluminum w/ Enamel Finish

Tube Fittings & Valves
316 SS Forged Body

Tubing
316 SS 1/4" .035 Welded

System Nameplates
Silk screened Lexan® & SS

Fastener Hardware
SS Screws & Bolts

Mounting Plate
316 14 Ga #3 Brush SS

EPCU Enclosed Body
Bead Blast Cast Alum.

Enclosure Warning

Nameplate
Silkscreened SS

The VT952ES is a NEMA 4X (IP66) LCD designed to meet Class 2, Div 1 protection. The purge system uses a pressure switch to automatically trigger alarms in case of pressure loss.
Slim and Economical
With its moderate weight and small footprint, the VT952ES series is ideal for
applications where both space and budget are limited.
Durable
The VT952ES monitors is fully enclosed in sealed, NEMA 4X (IP66), easy-open,
stainless steel cases. The chassis has no external vents, so nothing can get
under its skin, including weather, dust, dirt, moisture, oil, chemicals or other
harsh contaminants. A hard-anodized cast aluminum heat exchanger and
internal heat management system keep it cool in environments where ambient
temperatures approach 50°C/122°F -- without using outside air. With its lightweight yet rugged construction, and either pre-cabled or bulkhead connectors, the VT952ES display is easily mounted on walls, stands, arms or other industrial equipment.
The display is available with optional brackets, that conforms to VESA flat panel
mounting standards.

Display
19 Inch TFT, LCD screen shielded by a
Tempered Glass Protective Overlay

Resolution Capabilities
SXGA

Pixel Format
1280 x 1024*

Standard Connection
VGA, Serial, Power

Enclosure
316 Stainless Steel Sealed Anodized Aluminum Heat Sink
12" Handles

Environmental/Thermal
NEMA 4X (IP66)
Water Proof
Dust Proof
50ºC/122ºF
IP65

Purge System Mounting to Side (L/R), Top or Bottom

_____________________________________________________________

X Type Purge System w/ Pressure Switch (Class 2, Div 1 Protection)

This Rapid Exchange® purging system that operates on a supply of compressed
instrument air or inert gas. It regulates and monitors pressure within sealed
(protected) enclosure(s), in order to prevent combustible dust accumulation or
remove and prevent fl ammable gas or vapor accumulations. In Class II Areas, the
system maintains a "safe" (1.0") pressure. In addition, the system includes an
electrical power control unit (EPCU) that monitors system operation and controls
enclosure power. All start-up requirements must be satisfied before the EPCU will
energize power to the enclosure(s). These processes reduce the hazardous
(classified) area rating within the enclosure(s), in accordance with the NEC - NFPA
70, Article 500, NFPA 496 and ISA 12.4.

Shipping Weight
38 lb

Temp. Range
-20F to 120F

Supply Pressure Range
5 - 120 psi

Supply requirements
Clean air or inert gas

Safe Pressure Setpoint
.25"/1" @ safe pressure

Safe Pressure Flow Rate
0.1 - 3.5 SCFH - Enclosure integrity determines actual flow rate

Exchange Flow Rate
4 SCFM / 240 SCFH - With regulator set to 60 psi min. during exchange

System Supply Port
1/4" FPT

Enclosure Supply Fitting
1/4" tube fitting

Enclosure Reference Fitting
1/4" tube fitting

EPCU Conduit Port Size
1/2" FPT

EPCU Power Requirements
120 VAC 60Hz 10

EPCU Power Consumption
500mA

Dimensions
20" (H) x 11" (W) x 10.5" (D)
Height & Width dimensions reflect mounting plate measurements. Depth
dimensions reflects overall measurement of system, including components.

Mounting
Side (L/R), Top or Bottom

OPERATION

In accordance with system instructions, start-up requires the air supply to be
engaged and EPCU power to be energized. In Class II Areas, all dust must be
removed from the enclosure(s). The enclosure protection vent (if used) must be
tested and enclosure(s) must be sealed. The EPCU power control switch must be
activated and the system will self-test. The enclosure pressure control regulator is
then used to set a safe reading on the enclosure pressure gauge. In Class II Areas,
power will energize shortly after safe pressure is stable. Loss of safe pressure
causes the EPCU to de-energize power to the protected enclosure(s). All systems
include form "C" contacts for audible or visual alarm systems.